You have of store credit. To use it, simply place your order and you will be able to choose store credit as the payment method when it comes time to pay for your order.
Next Level Innovation Supported by multiple open source flight controller software including ButterFlight’s 3.3+ most current technologies Natively Fast True 32khz processing without...
FIRMWARE & MANUAL INTRODUCING IMU-Fa gyroscope that is filtered using advanced statistical methods to smooth noise trends. Instead of sending gyro measurements to the f4 it sends...
...
Description: Brand: Diatone Item name: Fury F4M flight controller MCU: STM32 F405 Six-axis: MPU6000 Flash: 16M OSD: AT7456 BEC: 5V 1A (burst current 1.5A) Input: 2-4S Lipo (7.4V-16.8V) Size: 30x30x5...
Specification: Weight: 5.6gram Size: 36MM*36MM PCB Thickness: 1.2MM Processor: STM32F405RGT6 Transmitter: MPU6000 integrated accelerometer/gyroscope Preset firmwareversion:3.1.7-OMNIBUSF4SD Signal of receiver...
Please Pay Attention to capacitor polarity while soldering , Reversed Polarity might cause Caps to burst. Voltage: 35v Capacitace: 2 x 1000uf SANYO Low ESR, High Freq...
SPECS: Power Supply:DC Voltage 2.8V~6.0VPower Consumption:50mA@5VReceiving Format:GPS,GLONASS,Galileo,BeiDou,QZSS and SBASReceiving Channel:72 Searching ChannelSensitivity:Trace -167dBm, Capture-148dBmPositioning...
IMPORTANT NOTE: This latest 2018 version (V1.4) is compatible with all ESC's, no matter how noisy they are. The CL_RACINGF4 and the CLRACINGF4S all using the same target "CLRACINGF4". DO NOT USE THE CL_RACINGF4 Target...
FC Specifications MCU: 168MHz STM32F405 IMU: MPU6000 accelerometer/gyro (SPI) Baro: BMP280 (I2C) OSD: BetaFlight OSD w/ AT7456E chip Blackbox: MicroSD card slot (SD/SDHC) VCP, UART1, UART2, UART3, UART4,...
SPECS: MCU: 100MHz STM32F411 IMU: MPU6000 OSD: BetaFlight OSD w/ AT7456E chip VCP, UART1, UART2, 6x PWM/Dshot outputs 2x LEDs for FC STATUS (Blue, Red) Built in inverter for SBUS input (UART1-RX) PPM/UART...
PLEASE UPDATE USING THE LATEST FIRMWARE FOR BUTTERFLIGHT AND BETAFLIGHT BELOW:After updating, please go to the console and type "imufupdate" see the documentation HERE FIRMWARE &...
Friendly Reminder: Upon receiving your FC, please connect to USB and calibrate before continuing to build and solder to it...
Specification: AMASS XT60 CURRENT SENSOR Voltage: 6S(25.2V) Current Max:120A Weight:6...
Specification: AMASS XT30 CURRENT SENSOR Voltage: 4S(16.8V) Current Max :80A Weight :3...
Specification:Item name: Ublox M8N GPSWeight: 10g Features:1. NMEA 0183 standard output2. Fast TTFF at low signal level3.RoHS compliant (Lead-free)4. UBLOX high sensitivity solution5. Jamming detection and...
Manual Download Specification: Model: HGLRC XJB F413-TX20.V2 Weight: 21.4g Usage: for 65mm-250mm Frame Kit Micro F4.V2 Flight Control Board ( D-Shot Version) MPU:...
HGLRC F4 Zeus F4 Flight Controller Integrated with OSD BEC PDB AIO 15A BLheli_S 4 In 1 ESC Manual Download Specification: Item Name: F4 Zeus Flytower F4 Fight Controller & 15A BL_S BB2...
DESCRIPTION A new generation AIO Flight control for FPV, based on F303 MCU, using F3 MCU controls OSD over SPI bus in DMA mode, OSD Configation has been incl. in Betaflight GUI. Supports SD Card and...
Features: F7 MCU - faster than the current F3 and F4 processors Two gyros on the flight controller: an MPU6000 for sampling up to 8khz and ICM20608 for sampling up to 32khz Built in betaflight...
FC Specifications MCU: 168MHz STM32F405 IMU: 32K ICM20602 accelerometer/gyro (SPI) Max. 32K Gyro update & 16K PID Loop OSD: BetaFlight OSD w/ AT7456E chip Blackbox: MicroSD card slot (SD/SDHC) VCP, UART1, UART2,...
Loading... Please wait...
